Details

---

Single Welding Hose 20 Bar is a softwall rubber hose intended for the transfer of oxygen or acetylene in welding and cutting applications. It combines a black SBR-blend tube, a coloured EPDM-blend cover and high-tensile synthetic yarn reinforcement. For supply or hose assembly enquiries in Malaysia, Advtech Engineering can review the required gas service, working conditions, hose size, length and end connections before quotation.

Single Welding Hose for Welding and Cutting Applications

This product is intended for single-line oxygen or acetylene transfer associated with welding and cutting equipment. The exact gas service must be identified before selection. A single hose should not be treated as an interchangeable line for different gases, and colour alone should never replace confirmation of the hose marking, system procedure and supplier information.

Published Product Construction

Component	Published information
Tube	Black SBR-blend compound with high impermeability
Cover	Blue, green or red EPDM-blend compound; abrasion- and weather-resistant
Reinforcement	High-tensile synthetic yarn
Temperature range	-20°C to +80°C
Safety factor	3:1

Understanding the 20 Bar Product Designation

“20 Bar” forms part of this product’s published designation. The allowable pressure of a complete hose assembly may also depend on hose size, fittings, attachment method, gas service, temperature, routing, condition and applicable equipment requirements. Confirm the complete assembly specification before use; do not select a hose solely from the product title.

Colour and Gas-Service Confirmation

The cover is available in blue, green or red. Required colour conventions can vary by gas service, site practice, equipment and jurisdiction. Before ordering, state whether the line is intended for oxygen or acetylene and confirm the required colour and identification method. Never rely only on visual colour where incorrect connection could create a hazard.

Information Needed for Selection and Quotation

• Gas service: oxygen or acetylene
• Required hose inside diameter and overall length
• Normal and maximum working pressure
• Operating and surrounding temperature
• Required cover colour and identification practice
• End connection type, size, thread and material
• Whether a loose hose or completed hose assembly is required
• Routing, bend, abrasion and outdoor-exposure conditions
• Applicable equipment instructions and site requirements

Hose Assembly and End-Connection Review

Fittings and attachment methods must suit the selected hose, gas service and equipment. Connection size or thread name alone is not enough: confirm thread form, sealing method, material and mating equipment. Advtech Engineering also provides hose assembly and fabrication support; final assembly requirements should be reviewed before production.

Installation and Routing Considerations

Route the hose away from hot surfaces, sparks, sharp edges, vehicle movement and avoidable abrasion. Avoid twisting, crushing, excessive tension and bends tighter than the hose or assembly recommendation. Provide sufficient length for normal movement without creating loose loops that can be damaged or become a trip hazard.

Inspection and Safe Handling

Only trained personnel should install and use gas-welding hose systems. Before use, inspect the hose, markings, cover, fittings and attachment areas for cuts, cracking, burns, abrasion, softening, leaks or movement at the connection. Isolate and depressurise the system before inspection, adjustment or replacement. Remove a damaged or suspect hose from service and follow the equipment manufacturer’s and site’s safety procedures.

Why Source Welding Hose from Advtech Engineering

Advtech Engineering supplies flexible hoses, couplings and fittings in Malaysia and can review hose and connection requirements using the information provided by the buyer. Browse the related gas hose category or contact our team with the operating details for a suitable quotation review.

Frequently Asked Questions

Is this hose for oxygen or acetylene?

The published description states that it is used for the transfer of oxygen or acetylene in welding and cutting applications. Specify one intended gas service when ordering and confirm the corresponding hose identification and system requirements.

Does “20 Bar” guarantee the rating of every completed assembly?

No. It is the published product designation. A completed assembly must be reviewed according to hose size, fittings, attachment, gas service, temperature, routing and equipment requirements.

What details should I send for a quotation?

Provide the gas service, hose size, length, required pressure, temperature, colour, end connections, quantity, routing conditions and whether you need loose hose or an assembled hose.

Need a Single Welding Hose 20 Bar quotation in Malaysia? Contact Advtech Engineering with your operating and connection details so our team can review the requirement before supply or fabrication.

Safety note: Product selection, assembly, installation and use must follow the hose and equipment manufacturers’ instructions, applicable rules and the site’s risk-control procedures. Suitability must be confirmed for the actual operating conditions.