Details

---

UHWMPE Chemical Discharge Hose 16 Bar is a softwall industrial hose described for handling a range of chemical, food, petroleum-product and oil media. Its published construction uses a translucent UHMWPE tube, a blue EPDM-blend cover, multiple layers of high-tensile synthetic cord and an embedded anti-static copper wire. Every application requires a media-compatibility and complete-assembly review before selection.

Chemical Discharge Hose Supply in Malaysia

Advtech Engineering supplies flexible hoses, couplings and fittings for industrial requirements in Malaysia. For a chemical discharge hose enquiry, provide the exact fluid and operating conditions so the hose tube, cover, fittings, seals and assembly method can be reviewed together. A broad product description is not a substitute for application-specific compatibility confirmation.

Published Hose Construction

Component	Published information
Tube	Translucent UHMWPE; described as resistant to aggressive chemicals and acids
Cover	Blue EPDM-blend compound; described as resistant to chemicals, abrasion and ozone
Reinforcement	Multiple layers of high-tensile synthetic cord
Static-control element	Embedded anti-static copper wire
Temperature	-30°C to +93°C; published note of 120°C for 30 minutes
Safety factor	3:1

Media Compatibility Must Be Confirmed

Chemical compatibility can change with the exact chemical name, concentration, purity, mixture, temperature, exposure duration and cleaning process. Confirm the intended medium against current manufacturer data before use. Where the medium is a mixture or trade-name product, provide its Safety Data Sheet (SDS). Do not infer suitability for an unlisted chemical from the hose material alone.

Understanding the 16 Bar Product Designation

“16 Bar” is part of the published product designation. The allowable working pressure of a complete hose assembly can also depend on hose size, temperature, fluid, fittings, seals, attachment method, routing, wear and pressure surges. Confirm the rated limits of every assembly component for the actual service before operation.

Temperature and Short-Duration Exposure

The published temperature information is -30°C to +93°C, with a note of 120°C for 30 minutes. The short-duration figure should not be treated as a continuous operating temperature. Compatibility, pressure capability, service life and assembly components must all be reviewed at the actual fluid and ambient temperatures, including cleaning or flushing cycles.

Static-Control and Electrical Continuity Review

The hose construction includes an embedded anti-static copper wire. This feature alone does not confirm the electrical continuity of a finished assembly. Where static charge is a risk, specify the site’s bonding or grounding requirement and have continuity verified across the completed assembly using the applicable procedure before service.

Information Required for Hose Selection

• Exact chemical or product name and SDS
• Concentration, mixture and purity
• Normal, minimum and maximum fluid temperature
• Working pressure, vacuum condition and possible pressure surges
• Required hose inside diameter and overall length
• Required flow rate and transfer frequency
• Fitting type, size, material, sealing method and gasket material
• Cleaning, flushing or steam-cycle details
• Routing, bend, movement, abrasion and outdoor exposure
• Static-control, testing and documentation requirements

End Connections and Hose Assembly Review

The fitting and seal materials must be compatible with the medium and operating conditions. Connection size alone is insufficient; confirm connection standard, thread or flange details, sealing face, gasket and mating equipment. Advtech Engineering provides hose assembly and fabrication support for requirements reviewed before production.

Installation, Inspection and Maintenance

Route the hose without twisting, crushing, excessive tension or bends tighter than the applicable recommendation. Protect it from sharp edges, heat sources, vehicle traffic and avoidable abrasion. Before each use, inspect the hose cover, markings, fittings and attachment zones for cuts, cracking, blistering, softening, corrosion, leakage or connection movement. Isolate, drain and depressurise the system before inspection or replacement, using controls appropriate to the transferred medium.

Food-Contact and Regulatory Requirements

The existing product description includes food media among its broad handling applications, but this does not by itself establish food-contact approval, hygiene certification or suitability for a specific consumable product. If the application has food, pharmaceutical or regulatory requirements, request and verify the relevant current documentation before selection.

Frequently Asked Questions

Can this hose handle my specific chemical?

Suitability cannot be confirmed from the generic product name alone. Send the exact chemical name, concentration, temperature, pressure, SDS and cleaning method for a compatibility review.

Is 120°C a continuous operating temperature?

No. The published information states 120°C for 30 minutes. Continuous service, pressure capability and compatibility must be evaluated separately for the actual conditions.

Does the copper wire automatically make an assembly electrically continuous?

No. The finished hose assembly, fitting attachment and bonding arrangement must be checked against the required site procedure. Where continuity is required, verify it before service and during scheduled inspections.

Need a chemical discharge hose quotation in Malaysia? Contact Advtech Engineering with the SDS, operating temperature, pressure, hose size, length, connection details and quantity. You may also browse our chemical hose range.

Safety note: Chemical hose selection, assembly, installation, testing and use should be performed by competent personnel using current manufacturer information, applicable rules and the site’s risk assessment. Replace any damaged or incompatible hose and follow the SDS and emergency procedures for the transferred medium.