Details

---

Cable Cooling Hose 10 Bar is a softwall hose used as a protective cooling sleeve for electrical cables in automatic welding systems. The published construction combines a white EPDM tube, a black Neoprene-blend cover, multiple layers of high-tensile synthetic cord and fibreglass cloth reinforcement. For selection, the machine layout, cooling medium, temperature, pressure, cable bundle and end interfaces should be reviewed together.

Cable Cooling Hose for Automatic Welding Systems

This hose is intended to sleeve and support the cooling arrangement around electrical cables used with automatic welding equipment. Correct sizing and routing help accommodate the cable bundle and normal machine movement. The final configuration must follow the welding-system manufacturer’s instructions and site electrical and mechanical safety procedures.

Published Hose Construction

Component	Published information
Tube	White EPDM compound
Cover	Black Neoprene-blend compound; described as flame-retardant, electrically resistant, abrasion-resistant and weather-resistant
Reinforcement	Multiple layers of high-tensile synthetic cord and fibreglass cloth
Temperature	-30°C to +100°C
Safety factor	3:1

Understanding the 10 Bar Product Designation

“10 Bar” is part of the published product designation. The allowable pressure of a completed cooling-hose installation can also depend on hose size, temperature, cooling medium, end connections, attachment method, routing, movement and equipment requirements. Confirm every component and the complete installation for the actual service before operation.

Cooling Medium and Temperature Review

State the exact cooling medium, concentration or treatment, normal temperature and maximum temperature. The published hose temperature range is -30°C to +100°C, but this does not establish compatibility with every coolant across the full range. Cooling performance also depends on flow, heat load, hose size and the equipment design; these must be confirmed by the system owner or equipment supplier.

Flame and Electrical Claims Require Context

The published cover description uses the terms flame-retardant and electrically resistant. No test standard, flame classification, dielectric rating or voltage rating is shown in the available product data. Therefore, the hose should not be presented as certified fire protection or relied upon as the primary electrical-insulation barrier unless current supporting documentation confirms the required performance.

Information Required for Selection and Quotation

• Automatic welding machine or equipment reference
• Cable bundle outside diameter and required hose inside diameter
• Required hose length and quantity
• Cooling medium and concentration, where applicable
• Normal and maximum pressure and temperature
• Required flow rate or equipment cooling requirement
• End-interface, fitting, clamp or termination details
• Machine movement, bend, travel and routing conditions
• Exposure to sparks, spatter, abrasion, weather or hot surfaces
• Required electrical, flame or testing documentation

Sizing and Routing Around Cable Bundles

Allow sufficient internal clearance for the cable bundle and cooling arrangement without crushing or excessive friction. Route the hose to avoid tight bends, twisting, pulling and interference with moving machine parts. Provide enough length for the full travel cycle while controlling loose loops that could snag, rub or contact welding spatter and hot components.

End Interfaces and Assembly Review

Confirm how the hose interfaces with the welding equipment, cable termination and cooling circuit. Connection dimensions, clamps or fittings must match the hose and actual operating conditions. Advtech Engineering provides hose assembly and fabrication support for requirements reviewed before production.

Inspection Before and During Service

Inspect the hose cover, exposed reinforcement, cable entry points, clamps and end interfaces for cuts, cracking, burns, spatter damage, abrasion, leakage, loosening or restricted movement. Isolate electrical energy and depressurise and drain the cooling circuit before inspection, adjustment or replacement. Remove a damaged or suspect hose from service.

Maintenance Planning for Moving Welding Equipment

Repeated flexing, heat exposure, welding spatter and rubbing can shorten hose life. Set inspection and replacement intervals according to the machine duty cycle, travel pattern, environment and inspection findings. After installation or maintenance, check routing throughout the complete movement range before returning the equipment to production.

Cable Cooling Hose Supplier in Malaysia

Advtech Engineering supplies flexible hoses, couplings and fittings for industrial users in Malaysia. Send the machine, cable, cooling and connection details for a requirement review. You may also browse the related hot-water and cooling hose category.

Frequently Asked Questions

Is this hose an electrical-insulation cable?

No electrical or dielectric rating is shown in the available product data. The cover is described as electrically resistant, but the hose should not replace the electrical insulation and protection required by the welding-equipment manufacturer.

Can Cable Cooling Hose 10 Bar use any coolant?

No universal coolant compatibility is stated. Provide the exact cooling medium, concentration, temperature and pressure so material compatibility and the complete circuit can be reviewed.

What measurements are needed for a quotation?

Provide the cable-bundle outside diameter, required hose inside diameter, length, machine travel, cooling conditions, end-interface details and quantity. Photos or drawings of the existing arrangement can help clarify the review.

Need a Cable Cooling Hose 10 Bar quotation in Malaysia? Contact Advtech Engineering with your welding-system, cable-bundle, cooling-medium and routing information for review before supply or fabrication.

Safety note: Selection, installation, testing and maintenance should be carried out by competent personnel following the equipment manufacturer’s instructions, applicable rules and the site’s isolation procedures. Confirm suitability for the actual mechanical, thermal, fluid and electrical conditions.