Details

---

Black Air Hose 10 Bar is a medium-duty rubber hose intended for compressed-air transfer in construction and general industrial applications. Its published construction uses a black SBR/NR tube, a black SBR/EPDM-blend cover and high-tensile synthetic-yarn reinforcement. Hose size, pressure, temperature, airflow, routing and end connections should be reviewed for the actual equipment.

Medium-Duty Compressed Air Hose in Malaysia

Advtech Engineering supplies flexible hoses, couplings and fittings for industrial compressed-air requirements in Malaysia. This hose may be considered for construction sites, workshops and general plant-air duties where the compressor and connected equipment conditions are clearly defined.

Published Product Construction

Component	Published information
Tube	Black SBR/NR compound
Cover	Black SBR/EPDM-blend compound; described as abrasion- and weather-resistant
Reinforcement	High-tensile synthetic yarn
Temperature	-25°C to +70°C
Safety factor	3:1

Applications Listed for This Air Hose

• Construction compressed-air service
• General industrial compressed-air transfer
• Workshop or plant-air lines after equipment review

These are general application descriptions. Confirm compressor output, connected tool requirements and site conditions before use.

Understanding the 10 Bar Product Designation

“10 Bar” is part of the published product designation. The allowable pressure of a completed hose assembly can also depend on hose size, air temperature, fittings, attachment method, wear, bend condition, pulsation and pressure surges. Confirm the complete assembly rating for the actual service.

Choosing Between 10 Bar and Higher-Pressure Air Hose

Do not select only by choosing the nearest pressure number. Review normal pressure, maximum compressor pressure, pressure surges, airflow, hose length, duty cycle, site abrasion and connection ratings. A higher product designation does not replace correct sizing or equipment compatibility.

Temperature and Worksite Exposure

The published temperature range is -25°C to +70°C. Consider both compressed-air temperature and ambient conditions, especially near compressor outlets, engines or hot equipment. Protect the hose from sharp edges, vehicle traffic, standing water, chemicals and other exposure not covered by the available product data.

Not for Breathing Air Without Specific Approval

No breathing-air approval or respiratory-air specification is shown in the available product information. Do not use this hose for supplied-air respirators, diving, medical air or another life-support application unless current documentation for the entire system specifically permits it.

Information Required for Selection and Quotation

• Compressor type, normal pressure and maximum pressure
• Air temperature and ambient temperature
• Required hose inside diameter and overall length
• Airflow requirement and connected tool or equipment
• Fitting type, size, connection standard and material
• Loose hose or completed hose-assembly requirement
• Routing, bend, movement and dragging conditions
• Outdoor weather, abrasion and nearby heat sources
• Quantity, testing and documentation requirements

Fittings, Couplings and Hose Restraint

Connections must suit the hose, pressure and compressor equipment. Confirm fitting size, connection standard, sealing method, attachment and any restraint required by site procedures. Advtech Engineering provides hose assembly and fabrication support for requirements reviewed before production.

Installation and Routing Guidance

Install without twisting, crushing, excessive tension or bends tighter than the applicable recommendation. Keep the hose away from vehicle routes, sharp edges, hot exhausts and pinch points. Where a separated pressurised hose could whip, follow the equipment and site requirements for suitable restraint and controlled isolation.

Inspection and Safe Depressurisation

Before use, inspect the cover, markings, fittings and attachment zones for cuts, cracking, blistering, abrasion, leakage, corrosion or movement. Shut down, isolate and fully depressurise the line before adjustment or replacement. Remove a damaged or suspect hose from service; do not rely on temporary wrapping for pressure-hose repair.

Black Air Hose Supplier and Enquiry Support

Send the complete compressor, tool, hose and connection details for a practical quotation. Advtech Engineering can review the supplied requirement information. Browse the related industrial air hose category for other published options.

Frequently Asked Questions

What is Black Air Hose 10 Bar used for?

The published description identifies medium-duty compressed-air transfer in construction and general industrial applications. Confirm the actual equipment and conditions before selection.

Can this hose be used for breathing air?

No breathing-air approval is shown. It should not be used for respiratory or life-support service without specific supporting documentation for the complete system.

Does 10 Bar apply to every completed assembly?

No. It is the published product designation. Hose size, temperature, fittings, attachment, wear and pressure surges must be reviewed for the complete assembly.

Need a Black Air Hose 10 Bar quotation in Malaysia? Contact Advtech Engineering with the pressure, temperature, airflow, hose size, length, connections, equipment and quantity.

Safety note: Compressed-air hose selection, assembly, installation, restraint, inspection and use should be handled by competent personnel following manufacturer information, equipment instructions and site procedures.